CS4364-CQZR【PDF 24/50 页】IC DAC 103DB 24BIT 6CH 48-LQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录1991

20页 21页 22页 23页 [24页]25页 26页 27页 28页

DS619F1

CS4364

4.14.2.2 IC Read

To read from the device, follow the procedure below while adhering to the control port Switching Specifica-

tions.

Initiate a START condition to the IC bus followed by the address byte. The upper 6 bits must be

001100. The seventh bit must match the setting of the AD0 pin, and the eighth must be 1. The eighth

bit of the address byte is the R/W bit.

After transmitting an acknowledge (ACK), the device will then transmit the contents of the register

pointed to by the MAP. The MAP register will contain the address of the last register written to the

MAP, or the default address (see Section 4.14.1) if an IC read is the first operation performed on the

device.

Once the device has transmitted the contents of the register pointed to by the MAP, issue an ACK.

If the INCR bit is set to 1, the device will continue to transmit the contents of successive registers. Con-

tinue providing a clock and issue an ACK after each byte until all the desired registers are read, then

initiate a STOP condition to the bus.

If the INCR bit is set to 0 and further IC reads from other registers are desired, it is necessary to initiate

a repeated START condition and follow the procedure detailed from steps 1 and 2 from the IC Write

instructions followed by step 1 of the IC Read section. If no further reads from other registers are de-

sired, initiate a STOP condition to the bus.

4.14.3

SPI Mode

In SPI Mode, data is clocked into the serial control data line, CDIN, by the serial control port clock, CCLK

(see Figure 23 for the clock to data relationship). There is no AD0 pin. Pin CS is the chip select signal and

is used to control SPI writes to the control port. When the device detects a high to low transition on the

AD0/CS pin after power-up, SPI Mode will be selected. All signals are inputs and data is clocked in on the

rising edge of CCLK.

4.14.3.1 SPI Write

To write to the device, follow the procedure below while adhering to the control port Switching Specifica-

tions in Section 2.

Bring CS low.

The address byte on the CDIN pin must then be 00110000.

Write to the memory address pointer, MAP. This byte points to the register to be written.

Write the desired data to the register pointed to by the MAP.

If the INCR bit (see Section 4.14.1) is set to 1, repeat the previous step until all the desired registers

are written, then bring CS high.

SD A

SC L

0011 00

ADD R

AD 0

R/W

Sta rt

ACK

DAT A

1-8

AC K

DA T A

1-8

ACK

Stop

N o te : If o pe ra tion is a w rite , th is b y te c on ta in s the M e m o ry A ddre s s P o inter, M A P .

No te 1

Figure 22. Control Port Timing, IC Mode

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式